01. Simulation and optimization |
||
|
Tanks are "framed" structures which are connected to the jacket in order to guarantee the required buoyancy during the jacket launching stage, as well as the subsequent self up-ending and floating phases ... |
 |
|
02. Structural analysis of a |
||
|
Structural analysis of the Castoro 6 pipeline lay vesse's external ramp lay for the as-built (damage d) geometry and for the strengthened geometric solutions at the regions of higher stress ... |
 |
|
03. Structural analysis of |
||
|
The system is a Multibore Quick Connect / Disconnect Coupler, which provides a simultaneous connection of pressure lines (risers) while guaranteeing the "structural" connection between the FPSO and its mooring lines ... |
 |
|
04. Finite element analysis |
||
Structural assessment of a Stinger for pipeline J-lay at different sea state loading conditions, utilizing finite element analysis and hydrodynamic analysis, in compliance with proper rules governing over the structural checks of offshore structures ... |
 |
|
05. Multi-body analysis of submarine |
||
Development of a submodel of a significant pipeline section having wet weight to be controlled by buoyancy tanks ..... |
 |
|
06. Structural analysis of an LNG |
||
Feasibility study of a system based on the principle of Multibore Quick Connect/Disconnect Coupler, that, besides the connections of pressure lines, guarantees the "structural" connection between LNG and loading arm .... |
 |
|
07. Parametric modelling, standardization |
||
Development of parametric finite element models for 8 distinct piping supporting saddle configurations with diameters from ½" to 72" .... |
 |
|
08. Stress analysis of a pipe bundle heat |
||
Structural integrity assessment of the heat exchanger E-208A/B during the start-up, service and shut-down phases ..... |
 |
|
09. Stress analysis of a ball valve |
||
Structural integrity assessment of valve-body and of valve-to-pipeline interface sections. The only reliable way to establish proper confidence over the valve structural behavior was the performing of analysis by means of dedicated finite element model ..... |
 |
|
10. Stress analysis for clapper impact effects |
||
Fluid-dynamics study and structural integrity assessment of shutoff valve body under impact load due to valve clap drop. The only reliable way to establish proper confidence over the valve structural behavior was the performing of analysis by means of dedicated finite element model ..... |
 |
|
11. PWDa |
||
Pressure While Drilling (PWD) simulation, manipulation and data analysis tool. The PWDa identifies the key phenomena which impacts annular pressure during well drilling of petroleum reservoirs ..... |
||
12. Simentar |
||
Software for simulation of the fluid circulation involved in oil well cementing operations .... |
||
13. SourSim |
||
SourSimRL is a simulator currently in use by most of the major oil and gas companies to avoid the formation of sulfide gas (H2S) during the secondary oil recovery process ..... |
 |
|
14. Simcarr |
||
SIMCARR ® is a simulator of hydraulic drilling and cleaning in vertical and inclined wells ..... |
||
15. P-52 adaptors |
||
Although a solution for the specific fatigue calculation was not available directly in ANSYS, ESSS has developed a solution that addressed Technip's needs ..... |
 |
|
17. Cold bending of thermally insulated pipes |
||
The project aims to determine the main parameters responsible by damage to duct bent cold ..... |
 |
|
18. Stress analysis of riser control pipes |
||
The primary objective of this project was to characterize the response of the Filler/control duct assembly when bent around a rigid tool ..... |
 |
|
19. Sleeve repair welding of in-service |
||
The primary objective of this project was to develop a computational model to represent the Sleeve Repair Welding process of In-Service Gas Pipelines ..... |
 |
|
20. Finite element modeling, fluid-dynamic |
||
Fluid-Dynamic and Structural verification of a portion of piping under different conditions (Installation, Hydraulic test, Start Up, Normal Run). Optimization of CupDisk® supports stiffness, in order to minimize stress state on the structure's supports ..... |
 |
|
21. Cyclone dust hopper influence |
||
The influences of the mesh, as well as the presence of a hopper were tested. Pressure drop: both, tetrahedrical and hexahedrical meshes ..... |
 |
|
22. A CFD study comparing different
feed |
||
To predict the fluid dynamic behavior in a coker fractionator washing zone and analyze the influence of vapor distribution on the heat and mass transfer efficiency, considering different number of inlet feed nozzles ..... |
 |
|
23. CFD as a feature to optimize vacuum towers |
||
A study was performed to verify the refinery vacuum tower feed inlet device modifications, comparing actual configuration to a future proposal. The study was based ..... |
 |
|
24. Numerical simulation of demister |
||
Create a methodology to simulate such equipment: preview the actual efficiency of the device; acquire detailed information on the gas/liquid distribution over the demister surface; compare with manufacturers data ..... |
 |
|
25. Efficiency comparison of tanks |
||
A study of the influence of the use of source points was performed ..... |
 |
|
27. Gravel packing case |
||
During well completion in deep or ultra-deep waters, sand contention is a big problem faced by petroleum engineers ..... |
 |
|
28. Fluid dynamic of a gas sparged |
||
Flotation process is a method for oil/water separation widely used in wastewater treatment ..... |
 |
|
29. Improvement of an optical oil and |
||
The aim of the present work is the study of the hydrodynamic flow inside an oil-in-water monitoring device for subsea production systems. |
 |
|
30. Multiphase modeling and fluid dynamics |
||
Mathematical model is able to reproduce the gasifier operation, presenting consistent results, which the solid recirculation is promoted even without the real cyclone effect ..... |
 |
|
31. CFD modeling of the combustion gases |
||
Ground Flare is provided for incinerating waste combustible gas. Each burner is composed by a great number of gas nozzles ..... |
 |
|
32. Modeling rock-fluid interactions |
||
Simulation of formation-acid reaction. Focus on accurate prediction of acid stimulation treatment ..... |
 |
|
33. Arc Welding - preliminary studies |
||
Electrostatic is phenomenon that charged body take on electric charge and discharge electricity. Plus and minus charged body come near together, gas between them ionize, after that electricity goes through ionized gas to another charged body. Ionized condition depend on degree of humidity, temperature, dust and EM condition. This condition does not only define EM condition ..... |
 |
|
© All rights reserved | ESSS North America Inc.